loading
| Availability: | |
|---|---|
| Quantity: | |
| Working Pressure | 1.4 MPa (14 bar) |
| Base | Propane carrier with premium silicone lubricant blend |
| Best Suited For | Tuned gas blowback pistols, high output rifles and custom gas platforms |
| Container Options | 300 g, 500 g, 1000 g canisters (bulk and industrial sizes available) |
| Operating Temperatures | 0°C to 45°C (32°F to 113°F) — warm for peak performance |
| Regulatory | Manufactured to meet applicable safety and transport regulations; SDS available on request |
Noticeable Power Increase: Higher working pressure produces greater muzzle velocity for improved effective range and target impact.
Realistic Blowback Feel: A sharper, snappier cycle enhances recoil realism and follow-up shot responsiveness.
Targeted Lubrication: The silicone content is tuned to protect seals and moving parts even under heavier cycling forces.
Consistent Output: Formulation minimizes mid-match power loss so FPS and cycle feel remain predictable over multiple magazines.
Optimized for Upgrades: Ideal fuel for guns with reinforced internals or aftermarket valve/seal upgrades that can safely handle 14 bar.
Pressure Characteristics: Nominal 1.4 MPa output designed to deliver a higher impulse per shot than standard green gas; pressure tolerances are tightly controlled during manufacture.
Blend Composition: Primarily propane, with performance additives and a measured silicone oil fraction to balance lubrication and residue control. No chlorofluorocarbon propellants.
Thermal Response: Gas transfer and pressure vary with temperature — slightly warming the canister improves fill consistency in cooler conditions.
Residue & Maintenance: Formulated to leave minimal clogging residue when used with routine maintenance; users should still inspect and service seals more frequently on high-output setups.
1.0 MPa (10 bar): Low output for stock/entry-level platforms — gentler recoil, lower FPS, excellent for preserving factory internals.
1.2 MPa (12 bar): Balanced mid range option — wider compatibility with good power and longevity tradeoffs.
1.4 MPa (14 bar): High-output choice — maximum BB energy among green gases, best for reinforced or modified guns. Requires confirmation of gun compatibility and more frequent maintenance.
Pick 1.4 MPa when your platform is built or rated to accept higher operating pressures and when you want stronger velocity and blowback.
We support OEM and private-label production: custom formulations within regulatory limits, bespoke labeling, variable canister sizes, and tailored packing. MOQ and lead times vary by specification; samples, tech sheets and labeling proofs are available upon request.
Batch Pressure Verification: Every lot is sampled to verify pressure output and tolerance.
Valve & Canister Integrity: Leak and valve function tests to ensure field reliability.
Lubricity Testing: Bench tests measure silicone distribution and lubricating efficacy on representative O-rings/seals.
Field Trials: Selected batches are validated in typical high-cycle gas-blowback platforms to observe wear patterns and performance stability. Non-conforming lots are rejected.
Storage: Keep in a cool, ventilated area away from ignition sources. Do not exceed recommended storage temperatures (≤50°C / 122°F).
Handling: Use upright; avoid crushing, puncturing, or incinerating canisters. Keep away from flames and sparks.
Personal Safety: Use in well-ventilated spaces; avoid prolonged inhalation. In case of dizziness or respiratory distress, move to fresh air and seek medical attention.
Emergency: For frostbite from gas contact, warm affected area and seek care. For spills/leaks, ventilate area and remove ignition sources
Disposal: Follow local rules for pressurized containers. Request SDS for detailed regulatory guidance.
Confirm Compatibility: Verify your gun, valve and seals are rated for 1.4 MPa before use.
Prepare Canister: If cold, warm the canister in your hands or a pocket briefly (do not use direct heat).
Refill: Hold the canister upright and depress into the fill valve until transfer ends (you may feel cooling).
Check & Cycle: Inspect for leaks, then perform a few dry cycles to ensure correct operation.
Maintain: Inspect O-rings/seals after high-pressure use and apply supplemental silicone oil as recommended by the gun maker.
Competitive & Tactical Players seeking added FPS and improved range.
Owners of Upgraded/Custom Guns whose internals are reinforced for higher pressure.
Specialist Retailers & Tuners offering performance parts and fuels for advanced users.
Q: Can I use 1.4 MPa in any gas-blowback gun?
A: No. Only use this gas in platforms that can safely accept 14 bar. Consult the manufacturer or a qualified gunsmith if unsure.
Q: Is 1.4 MPa the same as CO₂?
A: No. This product is propane-based and operates at lower absolute pressure/temperature ranges than CO- cartridges; the feel and hardware stresses differ.
Q: What maintenance is required?
A: Expect to inspect seals and O-rings more often than with lower pressure gases. Keep a supply of replacement seals and silicone oil on hand.
Q: How many shots per canister?
A: Shot count depends on gun efficiency and usage. A 500 g canister typically yields several hundred to ~1,000 fills worth of short transfers — actual BB counts will vary.
To order or discuss private-labeling, email: info@lyxinqiu.com. Ask for technical datasheets and the Safety Data Sheet (SDS) with your quote.
The 1.4 MPa Airsoft Green Gas (14 bar) is the high-output propellant option for players and tuners who need elevated FPS, crisp blowback, and dependable performance from upgraded airsoft platforms. Use it only in compatible systems and follow recommended maintenance procedures to get the best balance of power and longevity.
